what would cause a double ball feed on a Raced Warp Fed EVO Cocker , detent seems ok but get occasional double feed probs , warp is fed by a Halo B... thanks in advance
Raced Warp Fed EVO Cocker Problem
- Thread starter tiza5ive
- Start date
Should be using Ball Bearing Type ADB, rather than the Fang type Planet ones...other than that, maybe adjust the wheels on the Warp, so that they slip a fraction more, therefore, preventing DBL feeds. Intelli Feed? Could cause or solve this problem maybe?
If it's only happening when firing rapidly it could mean that your close time is set too low. Often overlooked, and in my experience very often wrongly set.
Don't play with the Warp feed-it weighs a tonne-also play with something more reliable like my Angel
thanks
thanks for the positive input Skeet + Rabies will try both these avenues.
Shog1 , best quit while you're ahead dude... you're the only person I know to cut down an IR3 trigger to make it a single trigger then bitch about your appalling rate of fire.... NUMPTY!!!
thanks again
thanks for the positive input Skeet + Rabies will try both these avenues.
Shog1 , best quit while you're ahead dude... you're the only person I know to cut down an IR3 trigger to make it a single trigger then bitch about your appalling rate of fire.... NUMPTY!!!
thanks again
Dude...if the close time is set too short, you will get problems with no ball loading, rather than two..I would think...but I am not familiar with the Race software, so my lerned collegue could well be right...SHOG on the other hand, seems to be a twat, if he wishes not to bear this label for long, he should learn the difference between constructive and usless comments.
Had he gone about saying why a Warp may not be ideal, I may have forgiven him..however, seeing as you use one, I would think you know what is good for you!! Statements like that are too be expected from persons who cut down triggers on IR3's I would imagine.....
Had he gone about saying why a Warp may not be ideal, I may have forgiven him..however, seeing as you use one, I would think you know what is good for you!! Statements like that are too be expected from persons who cut down triggers on IR3's I would imagine.....
nice one
Skeet thanx for the continued input m8...
however it is unfortunate that SHOG is a longtime teammate of mine who likes to "take da piss" if you get my drift..
will take the time to learn about what effect close and open times have on this piece of kit, but as it's newly aquired will take a little while to sink in properly.....
thx again
Skeet thanx for the continued input m8...
however it is unfortunate that SHOG is a longtime teammate of mine who likes to "take da piss" if you get my drift..
will take the time to learn about what effect close and open times have on this piece of kit, but as it's newly aquired will take a little while to sink in properly.....
thx again
dude email/pm/call Dangerous brian as I believe he uses the same setup, maybe not the halo. If he can't help you I will eat a piece of cauliflower!
You probably need to change your load and close timings.
Try dropping your load time (what loader did the previous owner have?), try 10-15millisecond - this is what Racegun recommend for Halo and Warp setups.
The close timing will then need to be reduce by 10-20% too.
Just remember that you will need to change these two settings if you decide to use a different hopper setup.
More information can be found here: http://www.racegun.dk
Try dropping your load time (what loader did the previous owner have?), try 10-15millisecond - this is what Racegun recommend for Halo and Warp setups.
The close timing will then need to be reduce by 10-20% too.
Just remember that you will need to change these two settings if you decide to use a different hopper setup.
More information can be found here: http://www.racegun.dk