My new setup
- Thread starter Dr_Chris
- Start date
Maybe your camera is a bit dodgy, it looks like one of the small flat bottomed bottles.
If it is then u want the drop the way u have it on the picture.
Otherwise you are gonna be a borg and everyone will laugh!!
Depending on teh setup...you can increase teh cap to whatever you like...however, if it will work, depends on the gat.
If you have a Cocker with QEV's a 44 Ram, delrin bolt, supercharger etc...then: Open grip, press red button above battery (with frame switched on), until TIMG appears in the display...Scroll down to CON, hit middle button, lower this setting to whatever you like, 20 is about as low as you can get while remaining useable, but I recommend that you put it back to 40 after you have been practising. Hit teh middle button again to set the value and then scroll to COFF...again, this can be as low as you like for fun factor, but useable levels are 18-25....
These settings will give you around 22BPS cap.
The reason I say set CON to 40, is, along with a COFF time of around 22...this equates to about 14BPS capability, if you have to turn your eye off during a game, due to failure, which is safe enough, if you are running a Z Eggy or HALO B/V35...
There are actually, ways to work out dedicated settings for your own personal gun, but mostly these settings are a good start, and certainly fast enough.
Also, for E1 users, lower your SON setting to 003...this controls the duration that the sear is disengaged for when you fire, if you go too low, the sear will go down and back up, before the hammer has moved, so wont fire!
CDEL...this can be used to help tune in Suction along with COFF...however, I'm not going to go into that right now...people who have standard E1's and upgrade to a 44/Nexus Ram and QEV's and a delrin Bolt...need to increase CDEL from 003 to 006, yes, longer!
The reason is, because the Ram operates so much faster.
CDEL, is the delay, between when you fire the marker (which releases teh hammer, opening the valve, and allowing air to flow), and teh Cocking solenoid switching on, to push open the bolt via the ram. If you dont increase teh delay, teh bolt will open while air is still flowing, which may cause drop off and blowback, not good.
I cant believe I actually sound liek I know what I'm talking about!!
Any other Tech heads out there, please feel free to correct me if I'm wrong.
CTO...this is the Time Out value...it is teh amount of time (250 ms, 1/4 second) that is allowed for the eye to detect a ball in teh breach, and is teh reason that teh gat will be slow, in Eye mode, with no paint. Leave it alone.
Max rof is calculated by: 1000 / CON+COFF+CDEL = Max ROF
Eg: CON 22 COFF 18 CDEL 6 = 21.74 Bps
If you have a Cocker with QEV's a 44 Ram, delrin bolt, supercharger etc...then: Open grip, press red button above battery (with frame switched on), until TIMG appears in the display...Scroll down to CON, hit middle button, lower this setting to whatever you like, 20 is about as low as you can get while remaining useable, but I recommend that you put it back to 40 after you have been practising. Hit teh middle button again to set the value and then scroll to COFF...again, this can be as low as you like for fun factor, but useable levels are 18-25....
These settings will give you around 22BPS cap.
The reason I say set CON to 40, is, along with a COFF time of around 22...this equates to about 14BPS capability, if you have to turn your eye off during a game, due to failure, which is safe enough, if you are running a Z Eggy or HALO B/V35...
There are actually, ways to work out dedicated settings for your own personal gun, but mostly these settings are a good start, and certainly fast enough.
Also, for E1 users, lower your SON setting to 003...this controls the duration that the sear is disengaged for when you fire, if you go too low, the sear will go down and back up, before the hammer has moved, so wont fire!
CDEL...this can be used to help tune in Suction along with COFF...however, I'm not going to go into that right now...people who have standard E1's and upgrade to a 44/Nexus Ram and QEV's and a delrin Bolt...need to increase CDEL from 003 to 006, yes, longer!
The reason is, because the Ram operates so much faster.
CDEL, is the delay, between when you fire the marker (which releases teh hammer, opening the valve, and allowing air to flow), and teh Cocking solenoid switching on, to push open the bolt via the ram. If you dont increase teh delay, teh bolt will open while air is still flowing, which may cause drop off and blowback, not good.
I cant believe I actually sound liek I know what I'm talking about!!
Any other Tech heads out there, please feel free to correct me if I'm wrong.
CTO...this is the Time Out value...it is teh amount of time (250 ms, 1/4 second) that is allowed for the eye to detect a ball in teh breach, and is teh reason that teh gat will be slow, in Eye mode, with no paint. Leave it alone.
Max rof is calculated by: 1000 / CON+COFF+CDEL = Max ROF
Eg: CON 22 COFF 18 CDEL 6 = 21.74 Bps
Sorry mate...I cant help it...I type fast now, but I think my fingers have just got into the habbit of doing it that way...I do go back and try to correct them...but sometimes
I CANT BE ARSED!!!
I CANT BE ARSED!!!
As I say, just keep the rail to what you have changed it. Makes the whole set-up a lot tighter and I guess you have probs got rid of most the hose also.