halo v35, what problem is this?

[westy880]

ACTIVATING THE LOADER :

1. PRESS AND RELEASE THE BUTTON IN REGULAR FASION

2. THE LOADER WILL NOW INDICATE WHAT MODE THE BOARD IS ON

3. THE LED INDICATOR WILL BLINK GREEN THE CORRESPONDING NUMBER OF TIMES FOR THE CODE INDICATION THEN BLINK RED ONCE

E.G. WHEN YOU TURN IT ON AND YOU ARE IN SETTING 3 IT WILL FLASH GREEN 3 TIMES THEN RED ONCE, AND THEN IT WILL BE WORKING.

TURNING OFF:

1. PRESS AND HOLD THE BUTTON UNTIL THE LOADER GIVES A RED INDICATION. RELEASE THE BUTTON AND THE LOADER WILL POWER DOWN AND BE OFF.

VICTORY CODES:

1. 17 BPS 4. 28 BPS
2. 21 BPS 5. 32 BPS
3. 24 BPS 6. 35 BPS


POGRAMMING:

TO ENTER PROGRAMMING MODE WITH THE LOADER

1. PRESS AND HOLD THE BUTTON WHEN THE LOADER IN AN OFF STATE UNTIL THE LED BEGINS TO FLASH

2. RELEASE THE BUTTON...THE LOADER WILL BEGIN OTO SEQUENCE THE CURRENT MODE.

for example 3 green flashes means you are in speed 3 - 24bps. now in programming mode, each time the button is pressed the program advances 1 time. press the button once per each advancement. when you have advanced to the setting that you want do not push the button any further. the setting you have chosen will repeat itself for 10 seconds then the loader will turn itself off, programming is complete.



hope that helps mate..

matt

 

[westy880]

just found this.

http://www.haloloader.com/_site06/pdf/manual_V35.pdf


has the manual on there.

 

[mikester]

cool. i'm in mode 3. that helps A LOT, thank you so much.


i'm slightly pissed i had to pay 5 quid for batteries on site now lol

 

[westy880]

not a problem mate. like i said, i had the same problem with mine. had to keep turning it on and off all day lol.

 

[foot]

how much is a new set of eyes?

I payed £6 for them.

 

[Dusty]

try your settings first, if the loader is anyway newish at all i can't see it needing new eyes.

 

[mikester]

try your settings first, if the loader is anyway newish at all i can't see it needing new eyes.

i only thought i needed new eyes cos when i stripped the halo, one diode was purple and the other was clear (as per photo), i just assumed one had burned out.

after advice from you guys it looks like the problem is fixed

i'm running mode 3 now after finding out how to use config. i think this is an ok speed as i'm using millenium mode which has ramping after 8bps so ups it to something quicker (sorry i don't know what exactly). so i'm thinking the halo speed of 24bps (mode 3) is going to be more than sufficient

 

[Bolter]

Also check the anti jam beads and spring are all there. With one bead missing it can cause jams.

Have you had it apart? Did you set the drive cone spring up ok? (the bit you have to lift it over the tab)

Other than that, only other thing is the paint. Ive seen paint thats got odd shaped paintballs in the bags, twin paintballs (2 molded together) etc. Im just thinking if it was cheap site paint, might have been jamming that way?

Thats all I got

 

[SAMUEL.D.RYAN]

If you want to check if your loader is on, just tap the button and it should show the current mode.

 

[onasilverbike]

As Dusty said, mode 1 is all you need, I suspect that the batteries were bad and/or cold and the current draw was too much or the balls jammed on the cone, if. indeed, it wasn't just user error and you had it in config!