e2 trigger prob

[A1-BOY]

, my sear and cocking solenoid arent clicking everytime i pull the trigger, it works most of the time when i pull the trigger hard and fast, but it wont work when you pull it slowly or on the side. ive tried adjusting the trigger loads, and changing the battery. and the same thing happens if its on training or semi. do i need to lubricate the sear, or take the cocking solenoid apart and clean it? or both?

thanks in advance.

 

[Skeet]

Is it a recent problem?

Have you fitted new grips to it that are letting excess light in?

Checked the wires on the solenoid/s?

Eyes off?

Wind out trigger stop screw a bit more?

Paint on the optical sensor?

 

[A1-BOY]

yep its a recent problem, i have just installed new grips, theres a bit of a gap, but it doesnt fire properly in a dark room either. the eyes are off, but its capped around 20, and i struggle to get ten. its not the trigger readjustment screws, cause i spent an hour yesterday experimenting, although it was a bit weird cause i could'nt get the actual point where it fires near the back of the pull at all. how could i check the solenoid wires exactly? and theres no paint on the optical sensor either.

cheers

 

[Skeet]

yep its a recent problem, i have just installed new grips, theres a bit of a gap, but it doesnt fire properly in a dark room either. the eyes are off, but its capped around 20, and i struggle to get ten. its not the trigger readjustment screws, cause i spent an hour yesterday experimenting, although it was a bit weird cause i could'nt get the actual point where it fires near the back of the pull at all. how could i check the solenoid wires exactly? and theres no paint on the optical sensor either.

cheers

OFFROF is set at 20 or max ROF is set at 20?

Eyes off cap is usually around 11-12 BPS.

Make sure the solenoid wires arent broken or pinched at all.

Its also worth checking...but...are you looking for the gun to fire, aired up...or air off and looking for clicking?

You can get all sorts of problems if the timing is out, so migh be worth setting it back to FACT FAST.

Same trigger?

 

[ollytheosteo]

I've seen similar problems a couple of times, one thing you can try is loosening the grip frame to receiver screws a bit and try firing again. The sear can sometimes bind on the slot in the body and produce those kind of symptoms. If that makes the solenoid click for each shot, then look at the side of the slots in frame and body for any wear to the anno.

 

[Sid Sidgwick]

Mine did the same once and it was a mix of two probs, I had the trigger wound in too far so it was always crossing the optical sensor and I had some muck on the cocking solanoid, unscrewing the trigger and a quick wipe of the solanoid sorted mine out mate

Sid

 

[Skeet]

Weren't Hybrid grips were they?

Didnt use a long screw on the top did you?

 

[A1-BOY]

current settings:

sear on: 4.0
c delay: 4.7
con : 22
c out :1.0
c off: 21

put it on factory fast, but no difference.

they are hybrid grips...not sure what you mean by long screw, i used the same screws as i had for my old grips...i beant the metal sheating to go round the sear. is that bad??

ive losened the grip frame screws a bit, didnt make any difference though, infact i think its worse lol.

 

[Skeet]

Try teh old grips again..see i fthat helps.

Long screws can damage teh Noid...I know its true for ego's, but I cnat remember if it is for E-Blades or not.

Bent teh shield around the sear?

 

[A1-BOY]

yer, my brother did it, hybrid grips have like a metal sheating beneath a rubber layer, he just bent it round the sear housing.

im just about to take my cocking solenoid apart and clean it. am i alright to use lovejuice?