Vlocity questions

[topchef]

Go on what's you Q...

BRAND NEW reloader B
BRAND NEW batteries

FRESH PAINT

shoots fine on semi. Increase BPS i.e 'ramp' or whatever and every now and then NOTHING.
Check eyes on gat and they are fine (poke finger down feedneck)

Use 'rip' and off we go again (for a short while) then have same problem....gat cuts out due to no balls being detected/fed into eyes on reloader.

Problem is persistent so I switch to back up hopper (vlocity)

I'm thinking JAM.
Maybe caused by old balls sticking together??
I check balls and all are good

No eyes on reloader, batteries are fresh, gun goes BANG (makes loud noise to activate relaoder), paint is good....


Any help appreciated.


-ChEf

 

[Jesus]

Mainly the viewloader range...Can strip an Egg & reassemble in 10 Min's..

blindfolded?

 

[Jesus]

Mainly the viewloader range...Can strip an Egg & reassemble in 10 Min's..

blindfolded?

 

[Will L]

BRAND NEW reloader B
BRAND NEW batteries

FRESH PAINT

shoots fine on semi. Increase BPS i.e 'ramp' or whatever and every now and then NOTHING.
Check eyes on gat and they are fine (poke finger down feedneck)

Use 'rip' and off we go again (for a short while) then have same problem....gat cuts out due to no balls being detected/fed into eyes on reloader.

Problem is persistent so I switch to back up hopper (vlocity)

I'm thinking JAM.
Maybe caused by old balls sticking together??
I check balls and all are good

No eyes on reloader, batteries are fresh, gun goes BANG (makes loud noise to activate relaoder), paint is good....


Any help appreciated.


-ChEf

Reloader B's do not have eyes they are sound activated. You will need to configure it to activate to the sound of your gun. Should tell you how in the manual but its an absolute must that you do it in a quiet place. Make sure you have configured it first.

Could just be the paint, what paint were you using and was it new? I know you mentioned fresh paint, but you also mentioned maybe old balls.

 

[Cliff-In2Deep]

BRAND NEW reloader B
BRAND NEW batteries

FRESH PAINT

shoots fine on semi. Increase BPS i.e 'ramp' or whatever and every now and then NOTHING.
Check eyes on gat and they are fine (poke finger down feedneck)

Use 'rip' and off we go again (for a short while) then have same problem....gat cuts out due to no balls being detected/fed into eyes on reloader.

Problem is persistent so I switch to back up hopper (vlocity)

I'm thinking JAM.
Maybe caused by old balls sticking together??
I check balls and all are good

No eyes on reloader, batteries are fresh, gun goes BANG (makes loud noise to activate relaoder), paint is good....


Any help appreciated..

-ChEf

This is common on these hoppers, but is sounds like your paint & the setting up of the hopper & also you said new batteries... What make as cheaper brands could be an issue...

blindfolded?

15 Min's blindfolded...lol...

Reloader B's do not have eyes they are sound activated. You will need to configure it to activate to the sound of your gun. Should tell you how in the manual but its an absolute must that you do it in a quiet place. Make sure you have configured it first.

Could just be the paint, what paint were you using and was it new? I know you mentioned fresh paint, but you also mentioned maybe old balls.

Like Will says check your set up in your manual for the configuration of your hopper...

Cliff...

 

[topchef]

This is common on these hoppers, but is sounds like your paint & the setting up of the hopper & also you said new batteries... What make as cheaper brands could be an issue...




15 Min's blindfolded...lol...




Like Will says check your set up in your manual for the configuration of your hopper...

Cliff...

Batteries are duracell (Used both '+' & procell's)
Paint has been 'chronic' & tomohawk finest

I know re-loaders dont have eyes etc, what I meant was the eyes on the gat (was tired last night).

Will have a crack at re-configuring it later and see how that gets on.

Cheers for the advice though lads

-ChEf

 

[Will L]

Changed the modes yet? What mode was it on in the first place?

 

[topchef]

Changed the modes yet? What mode was it on in the first place?

Not long got in from work fella, will have a bash in a bit and get back to ya

-ChEf

 

[topchef]

Righty then....

Just had a fiddle and found that my vlocity was in mode 7

Have followed Will's advice and it is now on mode 1. I put finger into feedneck and the light is now a solid green

So problem sorted

Muchos gracias matey

-ChEf

 

[Will L]

Thought so Seriously dont even think about putting it on anything higher than 1 though, before you 'may' have had to put it to mode 2 but with the new BPS rates mode 1 is perfect for it.