Not quite a pump question but
- Thread starter Andygoth
- Start date
Nice and cheap:
http://www.scenariodreams.com/productpages/ebladetboard.htm
I've heard strange things about their boards (funky quality control), so bear that in mind
http://www.scenariodreams.com/productpages/ebladetboard.htm
I've heard strange things about their boards (funky quality control), so bear that in mind
Full auto - WGP Select Fire Frame
Hi Mate,
A very basic but simple board with FA, 3 shot burst and ramp
http://www.pbnation.com/showthread.php?referrerid=210641&t=2401928
These were sold without the jumpers in EU to prevent full auto - you may be able to get a jumper from maplins for a few pence!
GEETEE had my one when upgraded my SF 05 Black Magic to an E1+ZB or I think Hawkins had one for sale awhile back.
http://www.p8ntballer-forums.com/vb/showthread.php?t=110932&highlight=frame
Hope this helps
Cheers
A
Hi Mate,
A very basic but simple board with FA, 3 shot burst and ramp
http://www.pbnation.com/showthread.php?referrerid=210641&t=2401928
These were sold without the jumpers in EU to prevent full auto - you may be able to get a jumper from maplins for a few pence!
GEETEE had my one when upgraded my SF 05 Black Magic to an E1+ZB or I think Hawkins had one for sale awhile back.
http://www.p8ntballer-forums.com/vb/showthread.php?t=110932&highlight=frame
Hope this helps
Cheers
A
Alan, let me know if you need the SF frame back. I managed to track down a black E1 frame in the end, so won't need it for the 1/2 blocker.
SF Frame
Hi Gary,
I do not need it, so it depends if Andy is interested?
Cheers
Alan
PS sorry i did not make the last Holmbush pump day, I am in the process of moving house.
Hi Gary,
I do not need it, so it depends if Andy is interested?
Cheers
Alan
PS sorry i did not make the last Holmbush pump day, I am in the process of moving house.
Arr, I don't know if "pump" ever got his eye to work with his MQ2 pump? Maybe he'd know what's going on. With a full auto slamfire setup, i'd imagine you'd run down the battery in about two minutes because the sear 'noid will be going nuts. You want the sear 'noid to trip only when there's a ball present, right?
No - the bolt would be in the rearward position.
You might be better of using an open bolt board. For an E-blade or whatever, the board will fire first in the cycle, then wait for the eye to tell it when to close the breach. Either way, I can't see it working without re-writing the eye logic.
You could set up a 2nd switch in series with the trigger sensor (in the pump handle or at the back block or maybe even at the eye hole.)
If you do that a scenario dreams board in semi will be fine - since it was the eye logic that was FUBAR. It would probably be foolproof as well.
I meant when there was a ball present and the eye detected it... (the forward position)
You just reposition the eye to infront of the detent so it only detects a ball that been pushed forward by the bolt.
If you use a board in semi mode then holding the trigger in does not fire the second shot, you would still have to pull the trigger for every shot. Putting the board in full auto and moving the eye means that if you hold the trigger in then the sear solenoid fires every time the gun detects the bolt has pushed the ball forward.
If you use a board in semi mode then holding the trigger in does not fire the second shot, you would still have to pull the trigger for every shot. Putting the board in full auto and moving the eye means that if you hold the trigger in then the sear solenoid fires every time the gun detects the bolt has pushed the ball forward.