Noob In need of help

[XVanUsX]

I am a noob and need some help if I could. I bought a package from a gentleman for my brother and I. It consisted of a 2000 wgp autococker (which I claimed) and a Pirhanna ext g2 i believe for my brother. I woudl like to know if anyone has anything paper wise or site wise that could show me the disassembly and assembly of these guns for cleaning and all. I have no manuals with them. I would also like a run down on actually what to do to get the guns setup to play. IE how to hook up the bottle and do I need to cock anything on teh gun or whatever. I tried to put the bottle and remote on teh pirahhna but the remote blew off the gun. SO i put it down. well thanks for reading!

 

[NiceButDim]

Have you had a look at the makers sites???

The piranha's site is http://www.pminetwork.com/

and the autococker http://www.worr.com/

they should be around that sites somewhere

 

[le-pig]

good cocker site
http://www.cockerownersgroup.com/

put a drop of decent airlube on the bolts o-rings(both markers),and a couple of drops in the gas inlets(where the bottles screw in)and dryfire 15 times.
this is all you really need to do appart from cleaning any paint of them
make sure the catch on the remote is lubed and moving/locking freely ie the coller pushes back to lock it
cya dave

 

[Parksy]

Big no no now putting oil in the screw in on any marker seemingly. Reports of exploding bottles in the states they think is being caused by this I used to do this with me STO until I read this, think it was on thecog or air-powered that i read it.

Dave

 

[JR_99]

Originally posted by L1f3
Big no no now putting oil in the screw in on any marker seemingly. Reports of exploding bottles in the states they think is being caused by this I used to do this with me STO until I read this, think it was on thecog or air-powered that i read it.

Dave

Sorry but that's rediculous.
What? Oil getting on the bottle threads will make it explode? Even if you put some oil in the bottle somehow it won't explode.
Too much preasuse leads to explosion.

 

[Parksy]

I didn't say it was oil getting on the bottle threads, it was something to do with oil getting into the tank....

 

[Munkeh]

Basically its when you have a very fine mist of Oil at high pressures it distincly lowers the flash point of it! Hence could, if the temperature starts to rise, set alight inside your tank! This = eeek!

 

[Parksy]

Cheers Andy, thought I wasn't imagining it

Dave

 

[ChrisWhiteSTEL]

Yeah, its like a combustion and compression thing, similar to a car engine cyclinder.

 

[TOOLE]

but anyway, i assume hat you are running on CO2, cos if you are, nothing mentioned on this thread would affect you as far as exploding goes.

for both guns, pull the bolt pin back on the gun, screw in the tank and fire it wihtout balls a few times, report any problems on here.


as for the remote set up, have you screwed everything on correctly? also, check the o-rings (little rubber rings) on the end of you're cannister. put a little bit of oil on that, and if there is not one there, get one and put it on.

both markers should fire fine after this.

for the autococker download this:

http://www.worr.com/images/autoschematic.jpg

for tthe pirahna try this

http://www.pminetwork.com/piranha_manual2.pdf


hope it helps

p.s. these rumours are fasle as far as exloding air systems go. gun oil, even when vapourised and pressurised, has an ignition temperature of over 140 *C, so unless you try to burn you're tank, nothing to worry about!!