New C&C Extreme Emag

[Collier]

Heres a pic :-

I put over 600 paintball's through her on Sunday using a VL200 (non agitating) didn't break 1 ball as much as I tried to short stroke and no matter how quickly I fired.
I mixed firing with the ACE on and off, I could rip a lot quicker with thee ACE off and still, with the level10 mod no chops Simply put the best marker I've used so far, obviously the real test will be on the field.

Paul.

 

[Walker (Nitro)]

chump.

EVERYBODY PAULS GOT A NEW PAINTBALL GUN!!!!!!!!! (or a very expensive sex toy)

 

[Collier]

Originally posted by Walker (PsychoPimps)
chump.

EVERYBODY PAULS GOT A NEW PAINTBALL GUN!!!!!!!!! (or a very expensive sex toy)

Chump?? I'll stick my finger in my breech, will you?


Paul

 

[manike]

Paul did you try both ACE settings? With a Halo, you don't necessarily need to use setting two because the halo is so fast. I was running mine with it on setting one and in hybrid mode... wowee long strings of paint at super fast speeds with no breaks in the 2 cases I put through it today.

only trouble is I only usually shoot 1 case at a practice hehehe

manike

 

[Collier]

Originally posted by manike
Paul did you try both ACE settings? With a Halo, you don't necessarily need to use setting two because the halo is so fast. I was running mine with it on setting one and in hybrid mode... wowee long strings of paint at super fast speeds with no breaks in the 2 cases I put through it today.

only trouble is I only usually shoot 1 case at a practice hehehe

manike

Nope didn't try setting 1 whats the differance?

Paul.

 

[manike]

Setting one has no delay at all from when it senses the paintball.

Setting two has a slight delay (20 milliseconds) from when it senses the paintball and is for two toned paint where it may detect too early on one of the colours. Or it's for a slow loader to make sure the ball is fully loaded.

So with single coloured paint and a Halo B you should be ok with setting 1.

With a slow rev or mutlicoloured paint where you get a few pinches on setting 1 then you will want to run setting 2.

Run setting one, and change it to setting two, if the gun pinches any balls.

You can also fine tune it further with the pot inside the gripframe so that it senses earlier or later, but be careful about messing with that if you don't know what you are doing .

I was runnning in hybrid mode on setting one fine all day. No pinches and very fast lines of paint.

manike

 

[Collier]

Originally posted by manike
Setting one has no delay at all from when it senses the paintball.

Setting two has a slight delay (20 milliseconds) from when it senses the paintball and is for two toned paint where it may detect too early on one of the colours. Or it's for a slow loader to make sure the ball is fully loaded.

So with single coloured paint and a Halo B you should be ok with setting 1.

With a slow rev or mutlicoloured paint where you get a few pinches on setting 1 then you will want to run setting 2.

Run setting one, and change it to setting two, if the gun pinches any balls.

You can also fine tune it further with the pot inside the gripframe so that it senses earlier or later, but be careful about messing with that if you don't know what you are doing .

I was runnning in hybrid mode on setting one fine all day. No pinches and very fast lines of paint.

manike

I see, I'll try that another time
I noticed on '.org you changed to a different carrier (1.5) after the o ring had broken in, can I expect the same thing? and how do I identify the different carrier's?
Have to excuse me, I'm being really lazy and not even looked at the different parts in the level 10 pack!
So whats the chances of blade triggers happening anytime soon?

Paul

 

[manike]

Oi! Go RTFM on AO

You may need to change down a carrier, it depends on your gun and which one it was set up with. You'll know if you do, and it's a 5 minute job.

I won't have time to work on blade triggers for a while. That's why I am trying to get one from the states also.

manike

 

[Collier]

Originally posted by manike
Oi! Go RTFM on AO

You may need to change down a carrier, it depends on your gun and which one it was set up with. You'll know if you do, and it's a 5 minute job.

I won't have time to work on blade triggers for a while. That's why I am trying to get one from the states also.

manike

RTFM??

If you get anywhere with Timmy63 can you grab me one as well? save messing about with 2 orders different address' etc

Cheers,

Paul.

 

[manike]

RTFM = Read The 'Fornicating' Manual.

It's something 'us' engineers refuse to do



manike