Dynasty Shocker...

[Skeet]

Peeps..my mate has just acquired a Dynasty Shocker...when it was aired up...wouldnt fire apart from farting...input preassure increased...fires but leaks from trigger...apparenlty has Evolve bolt setup etc...battery changed.

Need help guys as I dont know shockers...any ideas?

 

[Shep]

As regards to not firing just "farting" sounds like the bolts sticking due to too much lube or too little lube try removing bolt etc & inspecting,re-lube with dow33 7 try that.
A little concerned about the leak you say from the trigger frame is this when it fires or consistantly? as the shockers exhaust via the manifold when they fire, & can seem like a leak every time they fire(if not working correctly you can look for faults that arn't there).
If the leak is consistantly there when its aired up and your confident enough, remove the trigger frame & find out where its coming from most likely from the solonoid,if so check the seals on it at each end (or though it should be apparent where the leak is at that point)lightly lube them again with dow33 & rebuild air up & check if still leaking at that point & marker is under warranty contact SP. if not get a solonoid seal kit if possible(not sure if internal seals are available).
All I can think of at the moment will give it more thought, feel free to Pm me if no joy with these suggestions.

Oh yer I know my spelling sucks

 

[garycarrot]

Send it to "Evolve" and have it set up for you. Will cost you, but it will be worth it.

Be carefull if you are taking the grip frame off the body, as it is VERY easy to snap the on/off switch.

Hope that helps.

 

[Mikey D]

post on the forums at www.evolvepaintball.com
sounds like the front fire chamber may be the wrong way around.

oh and have you checked the dwell at all?

 

[Skeet]

Well...I saw the gun today...took it apart..checked for corect lubeing..all ok...clleaned some paint out of it...including the bit where the bolt is held in by an o-ring (is the is the fire chamber?)...checked solenoid screws and tweaked them a bit...put it back together..still has slight leak...BUT...apart from teh chrono not working properly...it appears the gun may have been doing 357fps...so..looks like too much input and not enough Dwell...maybe..I dont know about SP stuff in that way...so we will try that.

I have suggested that my mate get a full seal kit from Evolve so he has it...and also to try and geta Solenoid kit...I dont know if these are available...hopefully from Evolve rather than Rip Off merchants, SP.

The gun cycles and is pretty fast, so I'm guessing that means the the Noid is functioning...might just need the seals replacing or relubing...so...I will most likely get the job of rebuilding it!

Found a link to this wicked site tho...dunno if you guys have seen it....Shocker

I think its a Dynasty 04...how do I tell..and SFT, would it have that?

 

[jokersmoker]

Dunno if it helps skeet, but mike who was in our team had a stock shocker and fitted the evolve kit and that did nowt but leak, refit the old bolt, and fine again. i think he sent it back and got a replacement, which since has been no bother.

 

[Mikey D]

so skeet its working fine now? is it just a slight leak heard from the feedneck? Or still from the grip frame? Grip frame would suggest solenoid, and the solenoid kit would be worth looking into from evolve. Leaks (small ones) from the feedneck are usually just a matter of seals bedding in, or maybe just lubing the bolt again.
i think evolve bolts have a recommended dwell of 35beeps from the bottom (and i think rebound of 5, but i have mine at 0) just adjust the vert reg to get it down from there.
There isnt really an 03 and an 04 version, and SFT is part of all shockers. Look down the feedneck and there is am o-ring just before the barrel, this forms the seal forward technology part of the marker, nothing special so no need to worry about that.