ANGEL PIN Number

[pballerinLA]

I havent played for a bout 6 months. I pulled my Angel out to charge it up for tonight. When it was fully charged I turned it on and all it would say is PIN on the LCD. I dont have the manual, well I do its somewhere in the house... What is the default pin number, like the factory on?? Can I completely blow out the pin if I forgot it and start over?? PLEASE HELP.

 

[Collier]

Originally posted by pballerinLA
I havent played for a bout 6 months. I pulled my Angel out to charge it up for tonight. When it was fully charged I turned it on and all it would say is PIN on the LCD. I dont have the manual, well I do its somewhere in the house... What is the default pin number, like the factory on?? Can I completely blow out the pin if I forgot it and start over?? PLEASE HELP.

well you got two choices! datalink cable and sexy angel program, or see a wdp tech with your invoice! overwise your kinda screwed!

Paul.

 

[pballerinLA]

data cable

Do you have the data cable software? I can make a cable< i just need the software

 

[Collier]

data cable

Originally posted by pballerinLA
Do you have the data cable software? I can make a cable< i just need the software

Unfortunatley no, put a post on either PBnation.com or Paintballcity.com someone there will have a copy.

Paul.

 

[Mark]

Go to HERE the site was down for a while for updating but when it is running thats where the program could be found, careful using it though it cos it does come with disclaimers etc as to the damage it can cause (though everyone have said they have used it says it works ok) got to be honest I dunno if it will open your Angel without the PIN number but thats where you will find the program you asked for, but for the sake of the warranty I would get an Angel Tech to sort it. The same Program with the limitations of the display on an Angel will allow you to put a custom message like the "ROC ON" one found on the Rocky signature Angels. Be aware again that WDP do not authorise the use of the program, so screw it up and you will need a whole new board. the Angel forum and tech section found from the same pages will give you more info than you can imagine about what you can do electronically and otherwise, but the legal (country you live) and warranty issues make some of the advice a little suspect. SO DO IT ALL AT YOUR OWN RISK. think that was all clear enough..good luck.

 

[Mark]

Ah, update The Angel Owners Group is gone but hopefully the forum is still going, it is an Ezboard one so you will have to sign up for that to find someone who has the program you want. Ezboard can be found at http://www.ezboard.com

 

[Mark]

Ok having a bad day it isn't an Ezboard forum but then there is an Impulse, Shocker and Sterling forums on there so I guess it is a PBnation forum, I did sign up but I can't remember where it is cos I used the link from the Angel Owners Group so now I need help as to where the forum was/is...so help someone please.

 

[Collier]

Originally posted by Mark
Ok having a bad day it isn't an Ezboard forum but then there is an Impulse, Shocker and Sterling forums on there so I guess it is a PBnation forum, I did sign up but I can't remember where it is cos I used the link from the Angel Owners Group so now I need help as to where the forum was/is...so help someone please.

sorry mark, you lost mme there what link are you after now?

Paul.

 

[Mark]

The link for the correct server for the Angel forum I am a member but as I said I used the link from the Angel owners groups ...so I can't remember what server it was hosted on I thought it was Ezboard but as I said nope, so pbnation? pbcity? whatever one it is.

The Ezboard server has the Shocker and Sterling etc there but not Angel so thats the link I need.

 

[pballerinLA]

Software

I got all the instructions from other groups but I still don't have the software. That's what I need most now.