Bits I don't need anymore. Feel free to make an offer, but be sensible.
Postage not included, subject to requirements, within the UK only. Paypal payment owed, or +4%.
Rotor camo colour kit with top shell (normal capacity one, not extended), including the top and bottom side panels, lid with the pin included, in original packaging. The top panel is fixed onto the shell. Basically a full colour kit that's never been used, with a spare top shell thrown in.
SOLD to bhp addict
Freak kit with all inserts (two .693s, in fact), boxed. Two AC-threaded backs and one Ion back. Realtree APG guntape applied to All-American front, one of the AC backs, and the Ion back. The remaining AC back is dust black, without any marks. Underneath the tape, should you wish to remove it, the parts are gloss black. The anno should be in good condition, given the fact it's been covered.
SOLD to Geoff lee 01
Cure 2 bolt, straight out of my Ego 9, surplus as I have bought a Cure3+ bolt. Some minor scratch-marks on the plastic that I could not pick up with the camera; does not hinder performance in the slightest. Will include the plunger, the spring and the installation instructions which came with the Cure 3. Please note that you will need to use your existing bolt pin.
SOLD to MrP, pending payment
Dangerous Power G3 with a Virtue board and CP Shorty reg. The marker is dust black, the CP reg is silver, but Realtree APG guntape has been applied to most of the body and the barrel. This can be removed without a trace with a bit of spirit.
This was my backup a few months back, hardly ever used it. When I picked it up after a while it started behaving erratically. The bolt does not seem to travel all the way forward with every shot, and there is a great inconstistency in the velocity (as in roll-out-of-the-barrel-and-drop, to 290fps) . It's been suggested that it is a regulator issue, that it's been over-pressurized, someone even said that it might just be the lube... I don't know, and I don't have the time or the interest to tinker with it.
It will come boxed, both with the original and the Virtue manual, the CP reg and the Virtue board installed, as well as the original board and the original regulator. May be a five minute job for someone in the know and the bargain of a lifetime, or it may only be useful for spares. Nevertheless, the CP reg and the Virtue board are both quality components.
SOLD to jonboyyow
Postage not included, subject to requirements, within the UK only. Paypal payment owed, or +4%.
Rotor camo colour kit with top shell (normal capacity one, not extended), including the top and bottom side panels, lid with the pin included, in original packaging. The top panel is fixed onto the shell. Basically a full colour kit that's never been used, with a spare top shell thrown in.
SOLD to bhp addict
Freak kit with all inserts (two .693s, in fact), boxed. Two AC-threaded backs and one Ion back. Realtree APG guntape applied to All-American front, one of the AC backs, and the Ion back. The remaining AC back is dust black, without any marks. Underneath the tape, should you wish to remove it, the parts are gloss black. The anno should be in good condition, given the fact it's been covered.
SOLD to Geoff lee 01
Cure 2 bolt, straight out of my Ego 9, surplus as I have bought a Cure3+ bolt. Some minor scratch-marks on the plastic that I could not pick up with the camera; does not hinder performance in the slightest. Will include the plunger, the spring and the installation instructions which came with the Cure 3. Please note that you will need to use your existing bolt pin.
SOLD to MrP, pending payment
Dangerous Power G3 with a Virtue board and CP Shorty reg. The marker is dust black, the CP reg is silver, but Realtree APG guntape has been applied to most of the body and the barrel. This can be removed without a trace with a bit of spirit.
This was my backup a few months back, hardly ever used it. When I picked it up after a while it started behaving erratically. The bolt does not seem to travel all the way forward with every shot, and there is a great inconstistency in the velocity (as in roll-out-of-the-barrel-and-drop, to 290fps) . It's been suggested that it is a regulator issue, that it's been over-pressurized, someone even said that it might just be the lube... I don't know, and I don't have the time or the interest to tinker with it.
It will come boxed, both with the original and the Virtue manual, the CP reg and the Virtue board installed, as well as the original board and the original regulator. May be a five minute job for someone in the know and the bargain of a lifetime, or it may only be useful for spares. Nevertheless, the CP reg and the Virtue board are both quality components.
SOLD to jonboyyow
