Invert mini board!

[daniel.beenshill]

the board on my mini wont cap!

i switch it on it comes up with 1 flashing green light
10.5 bps on semi

so after about 2-3 shot it flashes red like the battery is dying but it just had a new one in

im not sure what to do because i want to sell it and dont have time to send it to mini to get it fixed!

 

[Bolter]

I don't quite understand. You turn it on, and its set to 10.5bps? What do you want to cap it to? 10.5bps is the lowest bps the 1.2 board will go.

What type of battery are you using? It shouldnt go to flashing red as quick as you say it is.

 

[daniel.beenshill]

im using a durecell battery. yeah i wanted it set to 10.5 but then it flashes red and then i switch it off and back on and it flashes very quickly!

 

[Bolter]

So it won't set to 10.5?

What EXACTLY do you when you are trying to set it. Like, walk me through the steps you take.

Or is it the battery issue you are worried about? Or do you think the battery going low is messing with the settings?

 

[daniel.beenshill]

Okay well let's say I put a new battery

1 turn off marker
2 remove battery
3 New battery in
4 then press the function button 2 times
5 wait for green light
6 press function button to lower bps
7 wait for flashes.. One green flash
8 turn on marker
9 add air system and rotor
10 shoot about 50 balls and then red flashing lights appear
11 turn off marker and back on
12 very quick flashing green light none stop
13 confusion..

Some times it doesn't even have to shoot!
When trying to switch it on it one red flash and won't
Switch on until you keep pressing the button!

Cheers dan

 

[Bolter]

Okay well let's say I put a new battery

1 turn off marker
2 remove battery
3 New battery in
4 then press the function button 2 times
5 wait for green light
6 press function button to lower bps
7 wait for flashes.. One green flash
8 turn on marker
9 add air system and rotor
10 shoot about 50 balls and then red flashing lights appear
11 turn off marker and back on
12 very quick flashing green light none stop
13 confusion..

Some times it doesn't even have to shoot!
When trying to switch it on it one red flash and won't
Switch on until you keep pressing the button!

Cheers dan

Seems you are doing the right things. You know when you change the battery, if you do it quickly, it doesnt lose your settings. Not normally anyway. Are you saying when you turn it off you lose settings?

Also I assume you are setting firing mode to "a" or 1 flash?

 

[daniel.beenshill]

Seems you are doing the right things. You know when you change the battery, if you do it quickly, it doesnt lose your settings. Not normally anyway. Are you saying when you turn it off you lose settings?

Also I assume you are setting firing mode to "a" or 1 flash?

Yeah when I switch it off it loses the setting but only sometimes yeah I'm setting the firing mode to 1 flash which should be semi auto?

 

[Bolter]

Yeah when I switch it off it loses the setting but only sometimes yeah I'm setting the firing mode to 1 flash which should be semi auto?

correct.

Have you had the gun apart? Im thinking (although its a long shot) that you havent connected something properly. I dont know if this would cause these issues or not.

 

[daniel.beenshill]

iv had it apart but everything seems to be in order think i should do it again make sure everything is in the right place!

 

[Bolter]

iv had it apart but everything seems to be in order think i should do it again make sure everything is in the right place!

Good idea!

Don't take the regulator apart though!

Does the gun shoot ok apart from all this?

Edit: by the way, this may be helpful http://www.p8ntballer-forums.com/vb/showthread.php?p=1037097#post1037097